Gas BarbecueUse, Care & Assembly ManualWith Grill Lighting InstructionsModel 9993 Series (LP Gas)ASSEMBLER/INSTALLER:Leave these instructions with
Grill Assembly (continued)105. Install one washer and ahairpin cotter on each pin(Fig. 26).Fig. 26Fig. 28Fig. 29Fig. 271. Insert the ends of the Propa
1. Align the tabs on the SideTables with the slots on theside of the grill (Fig. 35).Fig. 352. Use firm pressure to push theSide Tables down and intop
12Fig. 404. Check that all grill burner knobs are in the off position (Fig. 40).5. Remove the protective caps from the cylinder valve and coupling nut
13CAUTIONInspect the gas supply hose before each use. Lookunderneath the grill to inspect the hose assembly below thegrill. If there are cuts, damage,
14234WARNINGTHE FOLLOWING RULES MUST ALWAYS BE FOLLOWED IN THIS ORDER (Fig. 44):1. OPEN THE GRILL LID! Any attempt to light the grill withthe lid dow
CAUTIONDO NOT touch hot grill parts with your bare hands!You MUST use protective gloves.CAUTIONBe certain the gas is shut off at the L.P. cylinder val
16Burner Control Setting Tips• The high flame setting is too hot for direct cooking. The high flame setting is good for quick searing of meat, then fi
17CAUTIONAll cleaning and maintenance should be done only when thegrill is cool & with the fuel supply turned off at the cylinder.Suggested Cleani
182. Remove the cooking grates and heat tents and set aside.Using a screwdriver, remove the single screw holding eachburner tube. Push the burner tube
CAUTIONA collision with the grill, as with any metal object, could causeinjury. Use care when moving a portable gas grill.Moving the grill:• Move the
2DANGER• FOR OUTDOOR USE ONLY. NEVER operate grill in enclosed areas, as this could lead to gas accumulating from a leak, causing an explosion or a c
20TYPE 1 CONNECTION ILLUSTRATIONThermal Sensitive Handwheel1-5/16" Acme ConnectionNipple with Excess FlowValveRegulatorYOUR NEW GAS GRILL IS EQUI
Please do not send other correspondence to the address below.PRODUCT REGISTRATION DEPARTMENTPO BOX 2931 WICHITA ,KS 67201ATTN: DEPT 586IMPORTANT!Col
7) Side burner (if applies) 8) Steamer/Fryer/Warmer (if applies) 9) Side table design10) Color of the grill (not including stainless steel)11)
Replacement Parts List — 9993 Series23No. Part Number Description1 9993-4961 Thermometer Assembly2 9993-5051 Lid Handle Assembly3 9993-5151 Lid Assy C
The Coleman Company, Inc. • 3600 North Hydraulic • Wichita, KS 67219 U.S.A.1-800-356-3612 • TDD: 316-832-8707©2006 The Coleman Company, Inc. All righ
3• Installation must conform with local codes or, in the absence of localcodes, with either the National Fuel Gas Code, ANSI Z223.1/NFPA 54,Natural G
DANGER• DO NOT insert any foreign objects into the valve outlet. You maydamage the valve. A damaged valve can cause a leak, whichcould result in explo
5The pressure regulator and hose assembly with the Type 1 fitting suppliedwith the appliance must be used. Do not use another hose and regulatorassemb
137421. Grill Hood2. Thermometer3. Hood Handle4. Side Shelf5. Electronic Igniter6. Control Knobs7. Cart with Doors8. 120 VAC Electrical Outlet9. 120 V
Special Unpacking Instructions - 9993 Series7Fig. 71. Cut the shipping straps and remove the top of the cardboard container.2. Remove the door assembl
Fig. 138Parts Identification - 9993 SeriesIMPORTANT: Remove all packing material prior to assembly/use. If your grill has stainless steel components,r
Grill Assembly91. The Grease Diverter is installed without tools. It is to be located rightbelow the burners with four tabs inserted into four slots (
Kommentare zu diesen Handbüchern